Backup up an RV is a quite challenging task. Most of the time drivers have to convince their fellow passengers to go out and look at what’s going out there. For solo travelers, it becomes relatively more difficult to keep an eye on the surroundings.
Even if you’re a master of driving, still there are rare chances of getting your rig damaged due to an unnoticed obstacle.
Instead of wasting hundreds or thousands of bucks, many people opt for installing an RV backup camera. RV Backup cameras allow the drivers to travel to the campsite with confidence and without the constant fear of hurting any pedestrian.
Not only this, this inexpensive upgrade helps in making their journey easier and enjoy a worry-free drive to their destination.
Furrion RV Cameras – How They Work
Furrion needs no introduction in the world of technology and innovation. Ever since its advent, it has been featured many times in RV dealerships across the United States. It has been providing wireless RV cameras with innovative features.
Furrion RV cameras can be used as a reversing camera, tow hitch display, or security display, some features that only a few camera brands have been able to accomplish.
The 2.4GHz proprietary wireless Furrion RV camera has a wide field of view that enables one to see the area behind the rear bumper. It is pretty easy to install and can be set up in just ten minutes.
The weatherproof and stable camera provides night vision, and motion detection features along with a live feed up to 492 feet away.
But recently, there has been a record of reports that the Furrion RV camera is giving no signal error! What could be the solution for this? If you’re also facing the same issue, then check out these 5 fixes to get rid of this issue.
Furrion RV Camera No Signal – 5 Fixes to Try Out
1. Check Wirings
Wiring issues can be simply identified. They usually occur due to poor installation, wires being twisted, damaged, or bent inaccurately.
The most likely cause of the “no signal” error you are experiencing with the Furrion RV camera is primarily because of the camera’s power wire. Make sure that the connection between the Furrion RV backup camera and the display screen is not interrupted.
Just trace the wirings from the display screen to the backup camera to see where the disconnection has occurred and repair it.
If the connection is smooth, then start by examining the wires, if any of them had come off. If not, proceed to check if the wirings are connected correctly. The camera should be connected to the running lights and backup lights.
Each Furrion RV camera comes up with a manual, you can checklist all the wirings connections from that. If the wirings are made correctly, then one or more wires may have ended up undone or the wire may have been damaged.
Your system may have been set up using the cheapest wires and cables. The most realistic solution is to replace the wires or buy new ones for the system.
2. Analyze the Connectors
The connectors can also be the trouble. If your connector traitor is 7-pin, then the yellow wire refers to the reverse wire, while in the case of a 4-pin connector the yellow wire is for the left turn signal.
Ensure that all of them are connected rightly and tightly without any ambiguity. Verify that every pin in your connector is where it should be, and if not, move it there slightly.
Look if the pins are not broken, because they are delicate and a force can badly damage them. Sadly, in this case, you need to change your connector and purchase a new one.
If your camera is quite old or you’ve recently spent some quality time in a sandy or muddy area, dust might have collected in the wirings.
The dust will create an issue by declining the connection of the camera to the display screen. You need to remove the dust for the display screen to work properly.
3 Reset Your Display
If there is no uncertainty in wirings then the issue might be with the display screen. The display of “no signal error” on the display screen gives a hint to this being the issue. Remember if you’ve changed any setting of the display recently.
If yes, then the error is caused by the configuration. Trying to find the solution for that can be time taken. The best possible solution is to reset the display. Because it will remove the changes that might have been made mistakenly in the display screen’s settings.
All you need to do is to press the button on your display and hold it for a straight 15 sec. The device will shut down and start again. The display will be reset! Now, you’re reading to set the camera again. As instructed in the manual, set it as a rear camera.
Furrion’s main goal is to provide you with the best possible technology. The comfort of their clients has always come first. Because of this, they keep updating their camera features.
Most likely, you’re using an outdated version which could be the result of “no signal error”. To get access to the new version, you just need to reset the display screen.
Make sure that your camera display has selected the Firmware Updates option. Firmware is simply a term for software that allows hardware to function.
Furrion offers firmware updates, and if users don’t install them, their cameras become not only out-of-date but also extremely vulnerable to security risks.
Installing the most recent firmware secures your display screen, prevents a poor signal, and commonly brings awesome new features.
5. Faulty Display
If the no error signal still appears even after you’ve reset the display. It is a sign that your display is faulty. Connect your display screen to a computer to see if it will work. If not, the display itself is faulty and requires repairment or replacement.
Sometimes “no single error” displays because the device itself has reached the end of its life span. Electronics inside the display can malfunction, or environmental factors such as high levels of humidity may expose moisture inside the unit, and result in a short circuit.
However, it does imply that any particular component of the display is damaged, and a simple screen replacement will get functioning again.
5. Contact the Company Service
If all of these fixes become ineffective, the only option you are left with is to get in touch with your device’s support staff. Make sure you give them thorough information about the issue.
Establishing trusting relationships is the core of providing excellent customer service. Be clear about the issue and support staff will then present you with an effective solution. If the problem is still not solved, you need to check your camera’s warranty right away!
Each Furrion RV camera comes up with a guarantee with its manual. Most of them have a warranty of 1 year. But you can find out that on Furrion’s website, if you’re unable to, send them a mail at [email protected].
The team will contact you and inquire you regarding the camera, defect, and its warranty. But before that do make sure that the display wasn’t damaged because of your negligence or by a normal tear or wear.
After successful validation, the company will provide you with a new unit.
the signal of my furrion vision s is going in and out or signal, no signal. I have an acadia 2012 and it worked just fine. i just got an 2023 Tahoe and the signal is go for signal to no signal. what can i do.
Without sounding like a smarta**, I’d suggest buying another brand. I have a Furrion camera system that came with the fifth wheel camper I bought (NEW) and I’ve had nothing but trouble with it. My right side camera has NEVER worked, and both the left side and rear camera will work intermittently at best. I never know when they’re going to work and for how long. I’ve called the factory and they aren’t much help, I understand they need proof I bought the system but I have no proof because I did not receive anything when I purchased my camper; the cameras were already mounted on my camper, I only needed to hook up the monitor. Needless to say, I’m going to trash mine and buy a brand which will work consistently. Good luck trying to get yours to work.